HpLive Waterproof 1-Wire Digital Temperature Sensor Probe 5-Pack
HpLive Waterproof 1-Wire Digital Temperature Sensor Probe – 5-Pack Kit
Monitor temperatures with confidence using the HpLive Waterproof DS18B20-compatible 1-Wire Digital Temperature Sensor. Engineered for continuous submersion and harsh environments, this stainless steel probe delivers highly accurate readings across an exceptionally wide range — from freezing cold to scorching heat. Whether you're building a DIY aquarium controller, a home brewing monitor, a weather station, or an industrial automation system, this sensor integrates effortlessly with Arduino, Raspberry Pi, ESP32, and virtually any microcontroller platform.
Made in Mainland China.
Key Features
- Fully Waterproof & Rust-Resistant: Stainless steel probe sealed with thermally conductive sealant — built for continuous submersion, moisture-rich, and demanding environments.
- High Accuracy & Wide Range: Measures from -55°C to +125°C (-67°F to +257°F) with ±0.5°C accuracy for reliable, precise readings every time.
- Adjustable Resolution: 9–12 bit selectable resolution gives you full control over measurement precision versus conversion speed.
- Plug-and-Play Wiring: Color-coded leads — Red (VCC), Yellow (Data), Black (GND) — separated by heat shrink tubing for clean, mistake-proof connections.
- Broad Voltage Compatibility: Operates on 3.0V–5.5V, making it compatible with 3.3V and 5V microcontroller boards without additional power regulation.
- Integrated Pull-Up Resistor: Onboard adapter includes a pull-up resistor for direct Raspberry Pi GPIO connection — no external resistor required for basic setups.
- Simplified 1-Wire Protocol: All sensors share a single data line, reducing wiring complexity even in multi-sensor configurations.
Technical Specifications
| Temperature Range | -55°C to +125°C (-67°F to +257°F) |
| Accuracy | ±0.5°C |
| Resolution | 9–12 Bits (Adjustable) |
| Operating Voltage | 3.0V – 5.5V |
| Interface | 1-Wire Digital |
| Cable Length | 1 meter |
| Material | Stainless Steel Probe, PVC Cable |
| Size | 17 × 11 × 3 cm |
| Color | Black |
Package Contents (22 Pieces Total)
- 5 × Waterproof Temperature Probes
- 5 × 3-Pin Long Wires
- 2 × 3-Pin Short Wires
- 5 × Wiring Adapter Boards (with integrated pull-up resistor)
- 5 × 4.7kΩ Pull-Up Resistors
Compatible Platforms
Works seamlessly with Arduino, Raspberry Pi, ESP32, ESP8266, and most other 3.3V/5V microcontroller development boards.
Pro Tip
For optimal signal stability, use the included 4.7kΩ resistor between the Data (Yellow) and VCC (Red) lines when connecting without the adapter board.
Related Products You May Like
- Ancient Nutrition Multi Collagen Advanced Muscle 60 Capsules
- B&U 29mm Sinking Minnow Jerkbait Lure – Bass Trout Pike
Learn more: OSHA on personal protective equipment
Frequently Asked Questions
Q: Is this waterproof temperature sensor suitable for continuous water submersion?
A: Yes. The stainless steel probe is sealed with a thermally conductive, waterproof sealant specifically designed for continuous submersion applications such as aquariums, pools, hydroponics, and liquid temperature monitoring systems.
Q: Can I connect multiple HpLive 1-Wire sensors to a single microcontroller pin?
A: Absolutely. The 1-Wire protocol supports multiple sensors on a single data line. Each DS18B20-compatible sensor has a unique 64-bit address, so your microcontroller can read all sensors independently using just one GPIO pin, simplifying wiring considerably in multi-point temperature monitoring setups.
Q: What is the adjustable resolution, and how does it affect performance?
A: The sensor supports 9-bit, 10-bit, 11-bit, and 12-bit resolution. Higher resolution (12-bit) provides finer measurement increments (0.0625°C) but takes slightly longer to convert (~750ms), while lower resolution (9-bit, ~94ms) offers faster readings at coarser precision. You can set the resolution via software to match your application's needs.
Q: Does this sensor work with Raspberry Pi without an external resistor?
A: Yes — the included wiring adapter board has an integrated pull-up resistor, allowing direct connection to the Raspberry Pi GPIO without needing an external 4.7kΩ resistor. However, if you connect the bare probe without the adapter, use the included 4.7kΩ resistor between Data and VCC for stable operation.
Production & Packaging Notice
To maintain high stock availability and fast shipping times, our items are sourced from multiple verified manufacturing facilities. While the core quality, materials, and product specifications remain identical, you may notice slight variations in the packaging design, manufacturing origin, or the wording of the printed instructions.